Recycling an Old Fridge, Freezer and Washing Machine: From Kitchen to Smelter

· 8 min read

Divine Metal Recycling worker with a clipboard inspecting old fridges, chest freezers and washing machines lined up in the yard

Appliances don't last forever. You start to get problems with the fridge seal and the milk goes sour, the chest freezer starts to rattle and the washing machine will halfway through a wash just stop, leaving your laundry sitting on top of itself in a rather soggy state. So what do they do with them then?

When you think of an old appliance you probably picture it going in the bin. It gets sent to a metal recycling centre (Divine Metal Recycling for instance) where the valuable materials inside it (steel, copper, aluminium and so on) can be recovered and re-used. That's how it works.

In step 1 you'll be preparing for the removal!

Fridges and Freezers: Remove all food, shelves, drawers and loose trays and clean them. Just open the doors and leave them to dry for 1-2 days.

Washing machines: unplug the hoses, run out the water filter in the water pump and wrap up the power cord.

A frequent cause of injury when moving appliances is moving appliances. The fridges and freezers are obviously heavy and bulky, the washing machines can be quite heavy depending on what's in the drum. Two people should be used to lift them, a trolley and some straps would be the way to go. Fridges in particular must not be leaned over as this can put stress on the sealed system.

Call Divine Metal Recycling prior to booking and let them know what you're bringing and how you're going to get it to them. Can save a huge amount of time.

Divine Metal Recycling worker with a clipboard inspecting old fridges, chest freezers and washing machines lined up in the yard

The arrival and sorting at the yard are all recorded.

As soon as the appliance gets in, it gets identified and sorted. The cooling system in a fridge/freezer is a sealed refrigeration system which uses refrigerant and therefore requires special handling. Washing machines don't have any refrigerant in them (they're just very heavy because of the motor and the counterweights).

The reason for sorting is that all the materials have to be separated and cooling appliances in particular are an environmental hazard if not properly dealt with.

Third step: Cooling system

The fridge/freezer cooling system is made up of the cooling pipes, the sealed pipes and the compressor with the refrigerant gas in there. Older units may be lubricated with oil or some other such product.

Refrigerant handling is controlled in Australia and only a trained and qualified technician should handle refrigerants. Some refrigerants have a very high greenhouse effect and some of the older refrigerants can cause ozone depletion.

Never open the case, never poke into the system, never try and cut it up yourself. That may be the quickest way to get to the copper but you'll be releasing gas which should be safely recovered and it will make a right old mess. Leave the sealed system to the pro. Once the refrigerant has been recovered the appliance can then be dismantled.

Insulating foam can also be found along the side walls and doors of the fridge/freezer and you have to be careful with that as well given the nature of the foam. Refrigeration is far more than just a steel box with a motor in it.

Step 4: Dismantling

Take off the cooling system and the appliance can be disassembled. The aim of this is to separate out the various materials so that they can be sorted by type.

Contents of a fridge or freezer:

  • Steel: the outer casing which provides most of the steel's weight. Steel can be recycled infinitely without any loss of strength.
  • Copper: the compressor motor windings and some of the pipework.
  • The cooling plates and coils (and some of the pipework) are all aluminium.
  • Other materials are plastic shelving, drawer bins and trims, glass shelving and rubber door seals.

Inside a washing machine is:

  • Frequently painted metal panels: steel.
  • Separate the stainless steel to represent the drum which should not be mixed up with the regular steel.
  • Copper – motor windings and wiring (most of it).
  • Counterweights: the drums were held in place by large blocks of cast iron or concrete. That's essentially why the washing machine is so heavy.
Divine Metal Recycling bins sorted by metal, with copper motor windings in one bin and stainless steel washing machine drums in another

Mixed scrap is worth a hell of a lot less than separate bins of steel, copper and aluminium so it's absolutely vital that you dismantle carefully.

Step 5: Cleaning up the Metals

After disassembly the various metals are segregated: steel from steel, copper from copper, aluminium from aluminium. The stainless steel is separated from the 'normal' steel to prevent it reducing the load's value.

A simple test would be a magnet. Copper, aluminium and brass won't stick to it - plain steel and iron will. Extra care has to be taken with stainless steel as some grades are magnetic and some aren't. For some of the more experienced recyclers it's actually a skill to be able to identify most of the metals just by looking at them and by feel.

The cleaner the sort the easier it is to process and then sell. It's no frills labour really but it does have a massive impact on your metal value.

Step 6

The metals are sorted and weighed and then graded. The grade is determined by the type of metal, its cleanliness and its condition. Copper with no plastic attached is worth a lot more than copper with plastic on it – the same applies to steel.

Scrap prices are market driven and will vary according to supply and demand as well as the exchange rate. To get your payout get in touch with Divine Metal Recycling to find out what they're paying.

Step 7: Selling On and Remelting

The graded metal will be:

  • Steel is melted in a furnace and then used to make new sheets, beams and bars.
  • Copper is smelted and refined for use in electrical parts, pipes and wiring.
  • Aluminium is melted down and re-moulded and can be recycled indefinitely as the original material is not in any way altered.

Generally it takes less energy to make metal from scrap metal than it does to mine the metal. When a generation of fridges and washing machines are properly disposed of, they don't go to landfill. The metal in the old fridge could end up in a building, a car or new equipment. One day electricity could travel through the copper in the motor of your washing machine via the wall. The metal could be melted down and commingled with other metal and you'd never know where it ended up. Your appliance isn't the final destination. It's a store of materials which will be used again.

Tips

  • Drain and air dry.
  • Don't fiddle with the sealed cooling system.
  • Carry it properly with the appropriate equipment and a helper.
  • Please check with Divine Metal Recycling as to what they take and where to drop it off.

Do you have an extra fridge/freezer or washing machine that's taking up a lot of space in your basement? At least it's worth a lot more as metal. Call Divine Metal Recycling to find out about recycling!

Frequently Asked Questions

What can I do with an unrepairable fridge or freezer?

Yes. If it had stopped cooling completely it can still be recycled. The key thing is that the sealed system is intact in order to enable the recycling of the refrigerant.

What do I do to prep the fridge prior to drop off?

Get all the food out, clean up any spills and leave the doors open for a day or two to air out. It's a lot easier and safer to handle an empty dry fridge.

Why can't I just turn on the cooling myself?

Only a properly trained individual is qualified to do refrigerant recovery. Snipping the pipes will release the gas and that's dangerous.

What metals are in a washing machine?

They're likely to be steel (cabinet), stainless steel (drum), copper (motor) and wiring. Cast iron or concrete counterweights can be quite large. Varies by model.

Do I need to take the door off my fridge?

Not necessarily. All doors should be secured or, ideally, removed if the appliance is to be stored or left outside in accordance with local regs. Check with Divine Metal Recycling as to what they prefer.

Why is stainless steel any different from ordinary steel?

These are made from different materials. Stainless steel differs from regular (or "straight") steel because it is corrosion-resistant and more expensive.

Is the monetary amount paid a fixed amount each time?

No, not all scrap is equal, and prices fluctuate; please call Divine Metal Recycling to see what prices they offer for the metal you want to recycle.